Check and clean inside cooling coil if accessible: Foreign material on the coil reduces the system’s ability to cool the house, so your air conditioning system must run longer, increasing energy consumption and raising your cooling costs.
Clean primary and secondary drains: A clogged condensate drain causes considerable water damage and will increase humidity levels.
Check operation pressures for proper refrigerant charge: Improper refrigerant charges (too little or too much) can damage the compressor. This will cause high electric bills and reduce cooling capacity due to inefficient equipment operation.
Adjust and clean blower components: Proper adjustment and cleanliness of blower components is necessary for adequate air flow to assure maximum cooing performance.
Monitor air conditioning cycle: Our trained Servicemen will assure that the air conditioner is cycling on and off properly.
Lubricate all moving parts where applicable: Poor lubrication causes drag in the motor and drive shaft, thereby requiring more electricity to overcome resistance. This condition will cause early motor or bearing failure.
Monitor voltage and amperage draw on all motors: Motors are designed to operate at standard voltage and amperage draw. By measuring amperage draw, problems can be identified before the unit fails.
Check and tighten all loose electrical connections: Loose electrical connections are a common source of problems which cause your electrical parts to fail and your air conditioner to become inoperative.
Clean and adjust thermostat: To ensure even temperature control for your home.
Make Recommendations: To improve the operating efficiency of your air conditioner
Adjust and clean blower components: Proper adjustment and cleanliness of blower and components are necessary for adequate air flow to ensure your furnace can deliver maximum heating capacity and efficiency.
Check and test safety controls: Safety controls are essential for proper protection of the unit and your family. It will be adjusted to factory specifications.
Monitor furnace cycle: Our trained Servicemen will assure that the heating system is cycling on and off properly and that controls are calibrated to factory specifications.
Adjust gas pressure: Proper gas pressure to the burners will ensure the most efficient and safe burner operation while reducing energy costs.
Clean heat exchanger and burners: Dirty heat exchangers and burners reduce the efficiency and capacity of your furnace.
Thoroughly check for cracked heat exchanger: As your furnace gets older, there is a real danger of cracks developing in the heat exchanger. These cracks can allow dangerous products of combustion (including carbon monoxide) to enter the fresh air of your home and endanger your safety and the safety of your family. We will thoroughly inspect your heating system visually and mechanically to determine if this hazard is evident.
Monitor flue draft for safe operations: An obstructed flue can cause products of combustion to enter your home and endanger you and your family.
Adjust heat anticipator settings: The heat anticipator in your thermostat determines how often your furnace cycles and will affect the cost of operation, as well as the comfort level in your home.
Check and adjust pilot: A properly adjusted pilot will assure that your furnace will start reliably all winter.
Lubricate all moving parts where applicable: Poor lubrication cause drag in the motor and drive shaft, requiring more electricity to overcome resistance. Lack of lubrication can burn out a bearing motor.
Monitor voltage and amperage draw on all motors: Motors are designed to operate at standard voltage and amperage draw. By measuring amperage draw, problems can be identified before the unit fails.
Check and tighten all loose electrical connections: Loose electrical connections are a common source of failure.
Clean and adjust thermostat: To ensure even temperature control for your home.
Make recommendations: To improve the operating efficiency of your heating system.
Energy saving: Proper adjustment, lubrication and service to your heating and cooling systems keeps it running at peak, trouble free efficiency.
Reduced repairs: Many times our Servicemen will spot minor problems before they become major problems.
Preferred Customer: When your system does experience problems, you will receive priority dispatching to have your system back in operation quickly.
Discount on repairs: When repairs are required, you will automatically receive a 10% discount on all labor and parts charges.
Experts at your service: A competent factory trained, dependable staff of experts looks after your equipment to give you peace of mind. Our dispatcher will work with your schedule for convenience.
- 24 hour service: Our service department never closes. We are available 24 hours per day when you need us.
Automatic renewal: We will automatically extend your service agreement upon expiration. Naturally you are always free to cancel our service at any time with no penalty.
Ask our representatives for a planned service agreement. They have the prices and the simple one page form. Join our planned service customers today!
